Wind Turbine Blade Repair (Composites) SWMS
On-tower blade repair from rope access or BIP — composite (CFRP/GFRP) sanding RCS-equivalent dust hazard, resin sensitiser, lightning down-conductor inspection.
SWMS variants reference your state’s WHS legislation. Instant download after payment.
Wind turbine blade repair involves working at heights exceeding 80 metres on composite aerofoils using rope access or a blade inspection platform (BIP), grinding and sanding carbon fibre reinforced polymer (CFRP) and glass fibre reinforced polymer (GFRP) laminates, applying two-part epoxy resin systems, and inspecting lightning down-conductor receptors. The combination of fall exposure, respirable composite dust (which behaves similarly to RCS for lung deposition), epoxy sensitisers, and proximity to energised down-conductors triggers multiple high-risk construction work categories under WHS Regulation 2025 Schedule 1. A documented SWMS is mandatory before any blade campaign commences because the work is performed in a confined elevated envelope where rescue, communications and weather windows directly determine survivability. This SWMS aligns the rope access method, exclusion zones, dust capture and RPE program, and electrical isolation verification with the consultative obligations under s47-49 of the WHS Act and the record-retention duties under reg 300.
Hazards identified
7 hazards covered, sorted by priority.
Fatal impact or suspension trauma if backup line fails or rescue exceeds 15-minute physiological window
Pulmonary fibrosis, conjunctival irritation and long-latency respiratory disease equivalent to RCS exposure pathway
Irreversible Type IV hypersensitivity, occupational asthma and chronic contact dermatitis ending careers permanently
DC arc-flash burns, cardiac arrhythmia or fall reaction from unexpected shock during receptor inspection
Crush fatality or catastrophic injury from dropped load, sling failure or crane tip on uneven hardstand
Rope pendulum impact with tower, hypothermia and inability to complete controlled descent or rescue
CNS depression, flash fire ignition from static and chronic hepatotoxicity from repeated dermal absorption
Control measures
Hierarchy-of-controls order: elimination → substitution → isolation → engineering → administrative → PPE.
- 1Elimination — Schedule major laminate repairs to ground-based blade workshop where blade is removed, eliminating fall and on-tower dust exposure entirely where commercially viable.
- 2Elimination — Cancel rope deployment when 10-minute average wind speed at hub exceeds 10 m/s or lightning is detected within 30 km radius.
- 3Substitution — Specify low-volatility, non-sensitising modified epoxy systems (e.g. cycloaliphatic amines) in place of standard aromatic amine hardeners where structural spec permits.
- 4Substitution — Use pre-impregnated patch kits instead of wet lay-up to reduce solvent and free resin handling on the blade.
- 5Engineering — Deploy local exhaust ventilation shrouded sanders with HEPA H14 extraction captured at the tool head per AS/NZS 60335.2.69 dust class M minimum.
- 6Engineering — Verify isolation and apply earthing strap to lightning down-conductor with calibrated voltage detector before any receptor inspection per AS/NZS 4836.
- 7Administrative — Implement two-person rope team with GWO Working at Heights and Advanced Rescue certification, documented rescue plan and 15-minute suspension trauma threshold.
- 8Administrative — Conduct daily pre-start SWMS sign-on, METAR weather brief, and tool/PPE inspection logged against IRATA/SPRAT rope access logbooks.
- 9PPE — Full body rope access harness with sternal and dorsal attachment, helmet with chin strap to EN 12492, and Class 0 insulated gloves during conductor work.
- 10PPE — Powered air-purifying respirator (PAPR) with P3/TH3 hood, nitrile chemical gloves and Tyvek coverall during sanding and resin application per AS/NZS 1715.
Applicable Codes of Practice
Mandates written fall prevention plan, rescue arrangements and competency for any work above two metres including rope access blade campaigns.
Specifies rope, harness, anchorage and inspection requirements for the rope access system used to position technicians on blades.
Drives PAPR selection, fit-testing program and cartridge change-out for composite dust and epoxy vapour exposures during sanding and lay-up.
Governs isolation, testing for de-energisation and earthing of the lightning down-conductor system before receptor inspection or repair.
High-Risk Construction Work triggered
Rope access and BIP positioning on blades occurs 60-120 metres above ground with continuous fall exposure during traverse and repair.
Lightning down-conductor inspection and proximity to nacelle DC bus and overhead lines create arc-flash and induced-voltage exposure during repair.
Crawler crane is used to position the blade inspection platform, hoist materials and recover the BIP, creating suspended load and crush hazards.
PCBU must consult workers, prepare and retain the SWMS for the duration of the work plus two years after any notifiable incident; penalties for Category 1 breach are substantial and indexed, with the current maximum following the prevailing WHS schedule.
Who this is for
- →Wind farm O&M contractors on utility-scale assets
- →Rope access composite technicians (IRATA/SPRAT certified)
- →Renewable energy asset owners and EPC principals
- →WHS managers overseeing offshore-adjacent and remote wind sites
What you receive
- ✓Editable DOCX template — Microsoft Word compatible
- ✓State-specific WHS legislation schedule (NSW/VIC/QLD/SA/WA/TAS/NT/ACT)
- ✓Hazard register with risk ratings + hierarchy-of-control mapping
- ✓Worker sign-on register, pre-start checklist, and incident escalation flow
Worked example
On a coastal wind farm campaign repairing leading-edge erosion on a 75-metre blade, the lead technician opens this SWMS at the 06:30 pre-start brief inside the site container office. The two-person rope team and the crawler crane operator sign on after walking through the hazard register section, confirming the day's METAR shows 7 m/s gusting 9 m/s at hub — inside the 10 m/s elimination threshold documented in the controls. The lead technician identifies that today's scope includes a receptor inspection, so the SWMS prompts him to verify the lightning down-conductor isolation permit and apply the earthing strap before ascending. During the ascent, the support technician notes the SWMS-mandated PAPR cartridge change interval and swaps filters before sanding begins. Mid-task at 11:40, wind speed climbs to 10.4 m/s sustained; the technician references the SWMS trigger point, calls a controlled descent over radio, and the crane operator stands the BIP down. The crew re-signs the SWMS amendment register noting the weather stand-down and the partial completion of the receptor inspection, ensuring the next shift inherits accurate residual-risk information. The completed document is uploaded to the asset owner's compliance portal that evening, satisfying reg 300 retention obligations.
Related legislation
- WHS Act 2011 (model)
- WHS Regulation 2025
- AS/NZS 3000 — Electrical installations