Roller Door Installation SWMS
Safe Work Method Statement covering the key hazards and control measures for roller door installation.
SWMS variants reference your state’s WHS legislation. Instant download after payment.
Roller door installation covers industrial, commercial and domestic sectional and curtain-style doors, including tensioning of torsion or compression springs, mounting of head plates and guide tracks, and final motor and safety-edge commissioning. The work routinely involves elevated installation above 2 metres on stepladders or mobile scaffolds, manual handling of curtain assemblies frequently exceeding 80 kg, and the release and re-tensioning of stored mechanical energy in springs that can cause catastrophic strike injuries if uncontrolled. Under WHS Regulation 2025 sections 38 and 39, a PCBU must identify and control these risks before work commences, and where the task involves work at height with a fall risk exceeding 2 metres it is classified as high-risk construction work under Schedule 1, mandating a documented SWMS prepared in consultation with workers under section 47. This SWMS provides the structured hazard identification, hierarchy-of-control measures, and sign-on framework required to discharge those duties and to satisfy principal contractor verification obligations on commercial sites.
Hazards identified
7 hazards covered, sorted by priority.
Severe fractures to hands, forearms and face; potential fatality from spring bar strike to head or chest
Head trauma, spinal injury or fatality; notifiable incident under WHS Reg s35 with regulator attendance
Crush injuries to lower limbs, fractured pelvis or fatal asphyxiation from chest compression
Acute lumbar disc injury, shoulder rotator cuff tears and chronic musculoskeletal disorder claims
Electrocution, arc flash burns, cardiac arrhythmia; breach of WHS Reg s150 if unlicensed electrical work performed
Deep hand and forearm lacerations requiring sutures, tendon damage and risk of tetanus infection
Corneal abrasion, foreign body penetration, permanent vision impairment; lost-time injury reportable to insurer
Control measures
Hierarchy-of-controls order: elimination → substitution → isolation → engineering → administrative → PPE.
- 1Elimination — Specify pre-tensioned cassette or factory-balanced door units at design stage to remove on-site spring winding from the scope wherever the architect and client will accept the product substitution.
- 2Elimination — Schedule installation at ground level by lowering opening lintels via temporary works where structurally feasible, eliminating the work-at-height exposure entirely for head plate fixing.
- 3Substitution — Replace timber stepladder access with a certified mobile elevating work platform (EWP) or aluminium mobile scaffold compliant with AS/NZS 1576 for all work above 2 metres.
- 4Substitution — Use battery-powered impact drivers and cordless winders in place of mains-corded tools to remove trailing-lead trip hazards and reduce electrical risk at the work face.
- 5Engineering — Apply mechanical winding jigs or spring-tensioning tools with locking collars, and chain-block the barrel into brackets before any spring energy is introduced or released.
- 6Engineering — Install temporary edge protection or use harness anchor points rated to AS/NZS 5532 when EWP access is not practicable above 2 metres.
- 7Administrative — Restrict spring tensioning to workers holding documented manufacturer competency, isolate the work zone with bunting and signage, and conduct a pre-start SWMS sign-on with all crew daily.
- 8Administrative — Engage a licensed electrician for all 240 V terminations, lock out the circuit per AS/NZS 4836, and verify dead with a tested two-pole tester before motor commissioning.
- 9PPE — Cut-resistant gloves rated EN 388 Level 5, safety glasses to AS/NZS 1337.1, steel-cap boots to AS/NZS 2210.3 and impact-rated hard hat to AS/NZS 1801 worn at all times.
- 10PPE — Full-body harness and twin-tail energy-absorbing lanyard to AS/NZS 1891.1 connected to a rated anchor whenever working from an EWP basket or at unprotected edges above 2 metres.
Applicable Codes of Practice
Mandates hierarchy of fall controls for any work above 2 m, directly governing head plate fixing, barrel mounting and motor commissioning tasks.
Specifies mobile scaffold design, erection and inspection criteria used as the substitution control for stepladder access during guide and head plate installation.
Triggers risk assessment duty under WHS Reg s60 for lifting curtain rolls and motors exceeding safe single-person limits, requiring mechanical aids.
Governs lock-out, test-for-dead and terminate procedures for 240 V motor wiring and limit-switch commissioning at completion of installation.
High-Risk Construction Work triggered
Head plate fixing, barrel mounting and motor installation are routinely performed at 2.4–4.5 m above slab from EWP or scaffold, with unprotected edge exposure during transitions.
PCBU must prepare the SWMS before work starts, consult affected workers under s47, retain the document for the duration of the work plus two years post-incident, and provide it on regulator request. Penalties for Category 1 reckless breaches are substantial and indexed; current maximum follows the prevailing WHS schedule.
Who this is for
- →Carpentry and shopfit contractors installing commercial roller doors
- →Industrial door specialists fitting warehouse and loading-dock units
- →Principal contractors verifying subcontractor SWMS on Tier 2 projects
- →Owner-builders engaging trades for shed and garage door installs
What you receive
- ✓Editable DOCX template — Microsoft Word compatible
- ✓State-specific WHS legislation schedule (NSW/VIC/QLD/SA/WA/TAS/NT/ACT)
- ✓Hazard register with risk ratings + hierarchy-of-control mapping
- ✓Worker sign-on register, pre-start checklist, and incident escalation flow
Worked example
On a suburban industrial warehouse fit-out, the lead installer arrives to fit two 4.2 m high sectional doors to the loading bay. At the 6:45 am pre-start, the supervisor opens the Roller Door Installation SWMS on a tablet at the site shed and walks the two-person crew through the hazard register, pausing on the spring-tensioning and fall-from-height entries because today's work involves both. The crew confirms the hired EWP has a current logbook, the cut-resistant gloves and harnesses are inspected, and the manufacturer's winding jig is on the truck. Each worker signs the SWMS sign-on sheet, including the labour-hire apprentice who is briefed that he is excluded from spring tensioning and will act as spotter only. Mid-morning, the apprentice notices the original plan to use a mobile scaffold is impractical because of a forklift movement zone that cannot be isolated. The supervisor pauses work, returns to the SWMS, and documents a change in the control measure to substitute the scaffold for the EWP already on site, re-briefing the crew and re-signing the amended sheet before resuming. At handover, the licensed electrician arrives to terminate the 240 V motor supply, lock out the circuit, and complete the commissioning entry on the same SWMS, which is then filed in the principal contractor's site safety folder for verification.
Related legislation
- WHS Act 2011 (model)
- WHS Regulation 2025
- Managing the Risk of Falls at Workplaces CoP