Sliding Mitre / Compound Saw SWMS
Sliding compound mitre saw operations for finish-carpentry, trim and framing — slide lock, bevel and mitre angle setup, stock-securing with clamp, off-cut removal with riving push and hardwood-dust extraction.
SWMS variants reference your state’s WHS legislation. Instant download after payment.
Sliding compound mitre saws are high-speed wood-machining plant used across finish-carpentry, trim installation and light framing to deliver precise mitre, bevel and compound cuts on softwoods, hardwoods and engineered timber. The combination of an exposed rotating blade, sliding carriage travel, variable bevel and mitre geometry, and high-velocity hardwood dust generation creates a concentrated cluster of mechanical, respiratory and electrical hazards within the operator's immediate work zone. Under the Model WHS Regulations Chapter 4 Part 4.5 (Plant), a Safe Work Method Statement is required whenever powered plant with hazardous moving parts is operated, and AS/NZS 4024.3610 specifies the safeguarding, guarding and dust-extraction duties that the PCBU must demonstrate compliance with. A documented SWMS is the mandated mechanism for identifying these task-specific risks, selecting controls through the hierarchy, and recording worker consultation, sign-on and supervisor review before cutting commences. This SWMS covers slide lock disengagement, bevel and mitre angle setup, workpiece clamping, controlled off-cut removal and integrated dust extraction.
Hazards identified
7 hazards covered, sorted by priority.
Severe lacerations, partial finger or hand amputation, permanent tendon damage requiring microsurgery and extended workers' compensation claim
Projectile timber strikes operator's torso or face causing fractures, eye penetration injury or traumatic brain injury
Blade climbs workpiece causing loss of control, hand pulled toward blade and serious laceration injury
Nasal adenocarcinoma, occupational asthma, chronic obstructive pulmonary disease and reportable Schedule 14 health monitoring obligation
Ventricular fibrillation, cardiac arrest, severe burns and notifiable incident under WHS Act section 38
Permanent noise-induced hearing loss, tinnitus and successful hearing-loss compensation claim against the PCBU
Corneal abrasion, foreign body penetration, partial or total vision loss requiring ophthalmic surgical intervention
Control measures
Hierarchy-of-controls order: elimination → substitution → isolation → engineering → administrative → PPE.
- 1Elimination — eliminate freehand cutting of off-cuts shorter than 200mm by pre-cutting longer stock at the bench or specifying mill-cut lengths in the materials schedule.
- 2Elimination — remove the need to reach across the blade by positioning the saw so the operator approaches from the fence side only with clear off-cut fall zone.
- 3Substitution — substitute high-silica MDF and tropical hardwoods with pre-finished or lower-hazard engineered alternatives where the design specification permits substitution.
- 4Engineering — operate only saws compliant with AS/NZS 4024.3610 fitted with self-closing lower blade guard, riving knife where applicable, and functional electric brake stopping blade within 10 seconds.
- 5Engineering — connect M-class HEPA dust extraction directly to the saw shroud achieving minimum 20 m/s capture velocity to control hardwood dust at source per Workplace Exposure Standard.
- 6Engineering — use the integrated material clamp on every cut and engage slide lock for chop-mode cuts on stock narrower than 150mm to prevent carriage climb.
- 7Administrative — verify RCD protection on the supply circuit, complete pre-start inspection tag, and confirm blade is correct tooth count and rated RPM before first cut each shift.
- 8Administrative — establish a 1.5m exclusion zone around the saw bed marked with floor tape, restrict operation to workers who have completed documented competency assessment, and brief this SWMS at pre-start.
- 9Administrative — wait for blade to come to complete standstill before removing off-cuts, raising the head and re-engaging the lower guard between every cut cycle.
- 10PPE — wear AS/NZS 1337.1 medium-impact safety eyewear, AS/NZS 1716 P2 respirator for hardwoods, AS/NZS 1270 Class 4 earmuffs, and close-fitting sleeves with no gloves on the cutting hand.
Applicable Codes of Practice
Regulations 203–206 require risk management, guarding, isolation and information for plant with hazardous moving parts including powered mitre saws.
Specifies guarding geometry, riving knife dimensions, braking time and operator protection requirements directly applicable to compound mitre saw design and use.
Sets the PCBU duty for plant risk assessment, isolation, guarding verification and maintenance records that must support this SWMS.
Establishes the 8-hour TWA for hardwood dust triggering mandatory dust extraction, air monitoring and health monitoring under WHS Reg 368–378.
High-Risk Construction Work triggered
A sliding compound mitre saw is powered plant with a hazardous rotating blade and travelling carriage, meeting the Schedule 1 trigger when used on a construction workplace.
The PCBU must prepare, consult workers on, and retain this SWMS for the duration of the high-risk construction work plus two years after any notifiable incident; penalties for non-compliance are substantial and indexed, with the current maximum following the prevailing WHS schedule.
Who this is for
- →Finish carpenters and joinery installers on commercial fit-outs
- →Framing carpenters on residential construction sites
- →Shopfitters operating site-based mitre saw stations
- →Site supervisors verifying pre-start plant compliance
What you receive
- ✓Editable DOCX template — Microsoft Word compatible
- ✓State-specific WHS legislation schedule (NSW/VIC/QLD/SA/WA/TAS/NT/ACT)
- ✓Hazard register with risk ratings + hierarchy-of-control mapping
- ✓Worker sign-on register, pre-start checklist, and incident escalation flow
Worked example
On a mid-rise residential fit-out, a carpenter is assigned to install spotted-gum architraves across level 4. At the 7:00 am pre-start, the leading hand opens this SWMS on the site tablet and walks the two-person crew through the seven hazards on the saw bench set up in the back-of-house corridor. The crew identifies that the corridor is only 1.4 metres wide, so the standard 1.5 metre exclusion zone cannot be achieved — they apply the administrative control by relocating the saw to the lift lobby and marking the zone with yellow floor tape. The SWMS prompts verification of the M-class extractor connection and RCD test, both of which are signed off on the pre-start tag. During the first hour, the carpenter encounters a 120mm off-cut that needs to be trimmed; the SWMS chop-mode rule triggers engagement of the slide lock and the integrated clamp before the cut, rather than freehanding. Mid-shift, the extractor hose splits at the cuff — the operator stops work, the supervisor reviews the SWMS engineering control requiring source capture at 20 m/s, and cutting is suspended until a replacement hose is fitted. All four workers re-sign the SWMS after the control change, demonstrating the document functioning as a live risk-management tool, not a filed-and-forgotten compliance artefact.
Related legislation
- WHS Act 2011 (model)
- WHS Regulation 2025
- AS 2550 — Cranes, hoists and winches; AS 1418 series